Questions

How do I enable fast SSID on Cisco WLC?

Standard

How do I enable fast SSID on Cisco WLC?

Configuring Fast SSID Changing (GUI)

  1. Choose Controller to open the General page.
  2. From the Fast SSID Change drop-down list, choose Enabled to enable this feature or Disabled to disable it.
  3. Click Apply to commit your changes.
  4. Click Save Configuration to save your changes.

How do I reset my Cisco wireless controller?

Resetting the Controller to Default Settings

  1. Start your Internet browser.
  2. Enter the controller IP address in the browser address line and press Enter.
  3. Enter your username in the User Name text box.
  4. Enter the wireless device password in the Password text box and press Enter.
  5. Choose Commands > Reset to Factory Default.

How do I set the SSID on my Aruba controller?

Click Configuration, Wireless.

  1. Click Configuration, Wireless.
  2. Select a group and then click Networks.
  3. To create a new SSID profile, click the + icon.
  4. Under Basic Settings, configure the following parameters:
  5. Configure the following SSID parameters as required.
  6. Click VLAN to configure VLAN settings.

What is fast SSID changing?

When fast SSID changing is enabled, the allows clients to move faster between SSIDs. When fast SSID is enabled, the client entry is not cleared and the delay is not enforced. When fast SSID changing is disabled, the enforces a delay before clients are allowed to move to a new SSID.

What is WLAN SSID configuration?

SSID is a name given to a WLAN and is used by the client to access a WLAN network. profile and if the same zone is defined on a n Instant AP, the SSID. SSID is a name given to a WLAN and is used by the client to access a WLAN network. is created on that Instant AP.

How do I reset my Cisco 2504 wireless controller?

Resolution

  1. Enter reset system at the command prompt.
  2. At the prompt that asks whether you need to save changes to the configuration, enter Y or N.
  3. When you are prompted for a username, enter recover-config to restore the factory default configuration.
  4. Use the configuration wizard to enter configuration settings.

How do I setup my SSID?

Click Add SSID or select an existing SSID to configure….To configure an SSID:

  1. Open Discover.
  2. From the Navigator, select a location for the SSID. SSIDs are automatically inherited by subfolder locations. Make sure to select the correct top-level location when you create an SSID.
  3. Select Configure > WiFi.

How do I find my SSID in Aruba?

RE: Checking SSID’s In Aruba In AMP/Airwave, click on the access point and see if there is a hyperlink to the controller. Click on the controller to see if it has an IP address. Try to web into or SSH into the controller’s ip address.

How do I configure WLAN settings?

WLAN Configuration Example

  1. On the Navigation pane, click Configuration > Network > Network to visit the Network page.
  2. Select the ethernet0/1 interface and then click Edit.
  3. Click OK to save the settings.
  4. Select the wlan1 interface and then click Edit.
  5. Select the Enable DNS checkbox.
  6. Click DHCP.
  7. Click Add.

How do I remove the SSID from my Aruba controller?

In the New WebUI

  1. Navigate to the Configuration > Networks page.
  2. Under Networks select the WLAN. WLAN is a 802.11 standards-based LAN that the users access through a wireless connection. SSID. SSID is a name given to a WLAN and is used by the client to access a WLAN network.
  3. Click Delete Now to confirm deletion.

How do I access my Cisco wireless controller?

Both the wired and wireless clients can access the dynamic interface of the controller using the CLI and GUI. To access the GUI of the controller enter the dynamic interface IP address of the controller in the address field of either Internet Explorer or Mozilla Firefox browser.